Mad Scientist's Lair: table

We've been on a scrap-wood kick - trying to get rid of the extra plywood we have with some useful projects. One of these is a table for the backyard patio. The fountain turned our backyard into a nice oasis to chill out in, but it was still lacking something. Primarily a table, so that our back-porch picnics would have somewhere to put the food instead of just on our laps.
In our characteristic fashions, the Mr. wanted to just screw some plywood together, stain and seal it, and then call it a day. But the Mrs. had some more vibrant ideas, and after a quick trip to the local hardware store, we came back with some tile and mastic. Here's the story of the backyard table.

We cut out an (almost) equilateral triangle from one of the plywood scraps, rounded the corners, and sanded it to a nice finish. After this came two coats of stain and sealer.
Next we laid the tile out on the wood, marked the edges, and cut the tile with a Dremel equipped with a diamond cutting wheel (sorry no picture). This process took awhile, and should also be completed with proper safety precautions (safety goggles, dust-mask, and gloves).

Next up was the mastic and grout - a thin layer of mastic was applied on the surface of the wood, and we pressed the tiles into that. Once it had dried (24 hrs) we applied the grout to the tiles. We needed to start at the center tiles and work our way to the edges to allow the edge tiles some time to set. This way we didn't knock all the grout off when cleaning the tile surfaces. Moistening the cloth helped remove the drier grout from the top of the edge tiles.

After that the legs were attached with some hardware that we had laying around from when we built the bench. The screws going into the table-top are 1/4 inch plywood screws. With the metal bracket, they barely avoid going through the plywood.

With a couple of coats of grout sealer, we had a final product! The table nestles nicely between the two chairs when we have them angled towards the fountain, and is matched in height to the arms, so it's easy to use.

Tools:

Mitre saw
Jig saw
Power screwdriver ./ drill
Dremel
Protective devices (goggles, dust mask, gloves)

Cost:

$10 Tile
$5 Mastic
$0 Existing wood, screws.

We've finally finished the bedside tables! Here's a quick overview of the final steps, and a few pictures of the final product.
Left out is the cutting of the side panels and the doors. The side panels needed to fit flush, which was achieved by setting the jigsaw at a 45-degree angle for the long cuts along the side (See the picture below). I switched back to a straight cut for curve at the bottom and top of the side panels. The doors also needed straight cuts in for the hinges. After the sanding, staining, and sealing, we had the side panels and doors finished.

Once everything was stained, the doors needed to go on first, as I needed access to get to the hinges. I used quite a few washers to keep the screws from piercing through the thin 1/4 inch plywood.

We picked up a magnetic latch to keep the doors shut, and again used three or four washers on the door catch. Positioning the door catch required some dexterity; almost closing the door, then marking the horizontal and vertical position of the catch. The latch also required some distance tweaking so it was close enough to the edge to grab the door, but not far enough over to keep the door open, or be too obvious.

Here's the final product. The notches in each door, combined with the angled cut, allow them to open almost all the way. The sides are nailed into the shelves with small furniture nails. We're letting them air out in the study for a few days to loose the smell before we bring them upstairs, but other than that, they're finally done!

Here's the price tear down:
Tools:

Jigsaw
Mitre Saw
Power drill / screwdriver
Sander

Supplies:

Wood, stain, etc. was left over from the bench.
Hardware (angle brackets, hinges, door handles, washers): $30

Total:

Mad Scientist's Lair

Backyard Table

Bedside Tables - Part IV - Done!